RS PRO Bearing Puller, 8 pieces

  • RS Stock No. 349-7249
  • Manufacturer RS PRO
Technical data sheets
Legislation and Compliance
RoHS Status: Not Applicable
COO (Country of Origin): TW
Product Details

RS PRO Hydraulic Bearing Puller Set

This ergonomically designed Hydraulic Puller from our own RS PRO brand will eliminate time-consuming and unsafe hammering, heating or prying whilst on the job. Damage to parts is minimized through the use of controlled hydraulic power and it is easily operated by one person.

What to consider when choosing a puller for your job?

When choosing the right puller for the job, consider using a 3 leg puller if possible - this will give you better load distribution and is a lot safer in use

Spread of bearing puller? It is determined by the width of the part to be pulled.
Reach of bearing puller? It must be at least equal to or larger than the depth of the part that you need to remove.
Force of bearing puller? If you removing rusted parts or where there is a large area of surface contact, a greater force will be required. Consider choosing a puller which force screw diameter is at least half the size of the shaft on the item that you need to remove. Still not sure which puller to choose? Use the next largest simply because undersized bearing puller will slow down the job and nobody has time for that.

Features and Benefits

• High quality, forged steel provides superior reliability and service
• Precise hydraulic control allows fast, efficient and safe pulling
• Comes in a handy case which consists of hydraulic ram and nosepiece, main rod (200mm), thrust nut, extension rod (230mm), beam and bearing separator (4'')
• 10-ton hydraulic power unit
• Portable

Where could you use this RS PRO hydraulic puller?

• Motor repair shops
• Service company
• Mining
• Paper mills
• Chemical plants
• Shipping
• Offshore
• Maintenance shops

RS PRO

RS PRO is our own brand range and brings you a wide range of high-quality, great value products offering you more choice. Trusted by engineers all over the world, every part of every RS PRO product has been rigorously tested against demanding industry standards; they’re only given the RS PRO Seal of Approval if we’re confident of their exceptional quality, which means you can be confident too.

Note

For safety during bearing dismounting be sure to purchase an SKF TMMX 350 Puller Protection Blanket. RS Stock no: 732-4785

Specifications
Attribute Value
Hydraulic Force 10t
Operation Hydraulic
Number of Pieces 8
1 Within 1 working day(s) (IE stock)
42 Within 2 working day(s) (EU stock)
Unit of sale: Each
101.89
(exc. VAT)
125.32
(inc. VAT)
units
Per unit
1 +
€101.89
Related Products
The SKF TMHP 10E hydraulic jaw puller kit ...
Description:
The SKF TMHP 10E hydraulic jaw puller kit allows for the effortless dismounting of bearings up to 100 kN With self locking arms, the jaw puller minimises the risk of slipping even when under load. • Hydraulic spindle with safety ...
The SKF TMBS E series of back pullers ...
Description:
The SKF TMBS E series of back pullers are easily inserted between the bearing and shoulder on the shaft They have a spring loaded centre point allowing easier puller centring and a safety valve minimising puller overload. • TMBS 100E ...
The TMHS 100 hydraulic spindle from SKF generates ...
Description:
The TMHS 100 hydraulic spindle from SKF generates a high pulling force with only a small amount of effort Unlike standard mechanical spindles, they can dismount bearings in in a reduced time. The cylinder, pump and spindle are fully integrated ...
The TMMP series of standard jaw pullers are ...
Description:
The TMMP series of standard jaw pullers are versatile and one of the easiest and most effective ways to dismount small to medium size bearings Using an SKF mechanical jaw puller helps ensure that no damage is caused to the ...