ABB 2TLA020056R1000 Connection Cable, For Use With Pluto Safety Controller

  • RS Stock No. 733-2496
  • Mfr. Part No. 2TLA020056R1000
  • Manufacturer ABB
Technical data sheets
Legislation and Compliance
RoHS Certificate of Compliance
Product Details

Pluto Safety PLC, Base Unit

Pluto from ABB is an "All-Master" safety PLC concept, which simplifies the design of safety systems and achieves the highest safety category 4 according to EN 954-1. All Pluto's are Master units and can see the other Pluto's inputs, outputs and global memories. This enables the Pluto to evaluate the information from the other Pluto's and then take decisions concerning its own safety devices. The Gateway units are available for several different bus systems, i.e. Profibus (733-4836), CanOpen (733-4830), Devicenet (733-4849) and Ethernet (733-4842). Of Pluto's inputs (the smallest unit has 16 I/O), thus can be configured as either inputs or outputs. In the Pluto family by ABB most modules have dual safety outputs - potential free or PNP types. In a two-wire bus system up to 32 Pluto units can be safely connected and communicate with a superior system via a Gateway or HMI displays. Therefore within a maximum extended system 1472 I/O's can be connected. Also all input components may be connected in series for even more complexity and optimisation.

Simple and easy programming facilities
Easy to configure and install
Up to 640 I/O's
Multiple Plutos can be connected on a bus (via using the IDFIX identifier) and then further interfaced with external networks by using a Gateway, typical example RS stock number (733-4842)
High safety level
Free software available
Programming over the bus
35 mm DIN rail mounting
The IDFIX (733-4824) is an identification circuit which allows multiple Plutos to be identified when connected on a bus system. This module is available to distribute a PLC program within a network of Pluto devices.
Tina adapters such as (733-2477) can be used to connect external safety monitoring equipment

Note

The IDFIX device (733-4824) is connected between the input terminals ID and 0V (also note that the IDFIX device is not required when using a single Pluto, however the absense of an IDFIX requires to be stated when programming the Pluto device.)

Approvals

TUV, FS, CSA

Specifications
Attribute Value
Accessory Type Connection Cable
For Use With Pluto Safety Controller
Size 10m
Connector Size M12
13 In stock for delivery within 2 working days
Unit of sale: Each
33.28
(exc. VAT)
40.93
(inc. VAT)
units
Per unit
1 - 4
€33.28
5 - 9
€31.62
10 - 24
€29.97
25 - 49
€28.28
50 +
€26.63
Related Products
Smallest design Actuation only possible with BPS260, available ...
Description:
Smallest design Actuation only possible with BPS260, available separately Left-hand or right-hand side versions for door-mounting Control category up to 4 to EN954-1IP67 protection Connector 8 mm, 6-pole, latching interlocking Dimensions: L13 x W26 x H36 mm
The Schmersal 5m angled female connection cable is ...
Description:
The Schmersal 5m angled female connection cable is used with the BNS 260 safety switch It has an M8 6-pin connector size. Pre-wired cable6-pole Latching interlocking Straight design Operating current is 1.5A.
Simple installation and alignment with diagnostic indicators Automatic ...
Description:
Simple installation and alignment with diagnostic indicators Automatic / manual restart modes Robust IP65 enclosure Adjustable mounting brackets (included)External Device Monitoring (EDM)Dual channel, fail safe electronic outputs Mute and status outputs (non-safety)2 x mute inputs Safety category 4Typical ...
Description:
With no need for a separate safety relay this device saves space in the cabinet with no loss of functionality and is easy to install provides Cat 3//4 or SIL 2//3 protection on moveable machine guards or where frequent washdown ...