- RS Stock No.:
- 110-2371
- Manufacturer:
- RS PRO
Discontinued product
Alternative
This product is not currently available. Here is our alternative recommendation.
- RS Stock No.:
- 110-2371
- Manufacturer:
- RS PRO
Technical data sheets
Legislation and Compliance
- COO (Country of Origin):
- GB
Product Details
Single-Sided Microboards with Foil Laminate Holes
Development boards
Eurocard PTH microboard pcb made from copper laminated FR4 material
Medium packing density
Total flexibility using hard wire or wire wrapping assembly
Two Vcc power rails and 0V ground plane
Dimensionally compatible with IEC 297
DIN 41612 connector pattern front and rear
Printed grid pattern for easy reference
Coated with solder resist to reduce the risk of solder bridging
UL94 V0
Eurocard PTH microboard pcb made from copper laminated FR4 material
Medium packing density
Total flexibility using hard wire or wire wrapping assembly
Two Vcc power rails and 0V ground plane
Dimensionally compatible with IEC 297
DIN 41612 connector pattern front and rear
Printed grid pattern for easy reference
Coated with solder resist to reduce the risk of solder bridging
UL94 V0
DIN Type Stripboards
Suitable for use with the KM6-II eurocard sub-rack systems
The double-sided microboards are designed for microprocessor applications where compatibility, flexibility, high density and screening are of prime importance. VCC rails and a VCC bus are provided but not connected, so that individual rails may be committed as required. 64//96-way DIN 41612 indirect edge connectors may be fitted at either end.
The 3U (100x160) and 6U (233.4x160) boards are available with plated through holes (pth) as an alternative to the standard types. These boards have the added advantage of linking the top with the bottom pads directly via the holes, thereby dispensing with the need to fit linking pins, etc. Also the integrity of the joint is improved as the solder forms round the component lead on both surfaces, in addition to flowing through the hole. This helps to produce a solid and reliable connection, which is very important in applications where a high degree of vibration may be encountered.
Eurocards are manufactured from either epoxy glass material (blue) to BS4584 Part 3 or 16, or SRBP (synthetic resin bonded paper) material to BS4584 Part 5. Card thickness is 1.6mm. Copper 305g/m2 (1oz/ft2). Holes 1.0mm (0.040in.) dia. are pre-drilled on a 2.54mm matrix and all cards can be used with indirect edge connectors to DIN41612 (see Connectors/Terminals) except SRBP stripboard.
The 3U (100x160) and 6U (233.4x160) boards are available with plated through holes (pth) as an alternative to the standard types. These boards have the added advantage of linking the top with the bottom pads directly via the holes, thereby dispensing with the need to fit linking pins, etc. Also the integrity of the joint is improved as the solder forms round the component lead on both surfaces, in addition to flowing through the hole. This helps to produce a solid and reliable connection, which is very important in applications where a high degree of vibration may be encountered.
Eurocards are manufactured from either epoxy glass material (blue) to BS4584 Part 3 or 16, or SRBP (synthetic resin bonded paper) material to BS4584 Part 5. Card thickness is 1.6mm. Copper 305g/m2 (1oz/ft2). Holes 1.0mm (0.040in.) dia. are pre-drilled on a 2.54mm matrix and all cards can be used with indirect edge connectors to DIN41612 (see Connectors/Terminals) except SRBP stripboard.
Note
Single-sided microboards have the same wiring pattern as the double-sided types, but omit the ground plane and 0 Volt rails on the component side of the card.
Specifications
Attribute | Value |
---|---|
Base Material | Epoxy Glass Fabric Laminate |
Number of Sides | Single Sided |
Dimensions | 233.4 x 220 x 1.6mm |
Hole Diameter | 1.02mm |
Hole Pitch | 2.54 x 2.54mm |
Connection | DIN 41612 |
FR Material Grade | FR4 |
Length | 233.4mm |
Thickness | 1.6mm |
Width | 220mm |